How to Start a Stubborn Chainsaw

To start a stubborn chainsaw, begin by making sure that the chain brake is engaged and fuel tank is full of clean, fresh fuel. Make sure all air vents are clear of debris and the spark plug wire is connected securely to the spark plug. Pull out the choke lever for cold starts or push it in for warm starts.

Set the throttle control knob to half-throttle position if your saw has one. Hold down firmly on both handles as you pull on starter rope until engine fires up – usually no more than 4 pulls are needed. If necessary, adjust carburetor settings with idle speed screw and mixture screw until engine runs smoothly at full speed.

Finally, make sure all safety features are working properly before operating your chainsaw again.

  • Check the fuel: Before attempting to start a stubborn chainsaw, make sure that it has enough fuel in it
  • This will ensure that the engine is receiving adequate energy to turn over and start up
  • 2
  • Inspect spark plug: If the chainsaw does not have enough fuel, then check if the spark plug is working correctly by removing it from its housing
  • Clean off any debris or dirt from around the electrodes on either end of the plug before replacing it back into its socket in order to ensure proper functioning of this component
  • Prime carburetor: Priming a carburetor involves supplying just enough gasoline into an engine’s intake manifold so that when an ignition source occurs, combustion can occur more quickly and easily than having to wait for air/fuel mixture within a cold-start situation where vaporization of gasoline takes longer time due to cooler temperatures inside internal combustion engines cylinder head and crankshaft area; this priming process helps eliminate hard starting issues associated with certain fuels such as ethanol blended ones which require additional energy input (from priming) during colder weather conditions in order for them to ignite more reliably given their lower octane rating compared to non ethanol options like regular unleaded gasolines typically used by most small engine powered devices including lawnmowers, snowblowers etc
  • 4 Pull starter cord: After completing these steps above, pull on the starter cord several times until you hear or feel some resistance from within your chainsaw – this indicates that compression buildup inside cylinder chamber walls has occurred thus allowing for better chances at successful startup attempts via sparkplug firing sequence initiated after pulling starter cord again vigorously but steadily until motor turns over and starts running normally; keep safety goggles & gloves on at all times while operating power tools such as chain saws!
How to Start a Stubborn Chainsaw


How Do You Start a Chainsaw That Won’T Start?

If your chainsaw won’t start, there are several steps you should take to diagnose and fix the problem. First, ensure the fuel level is adequate and that you’re using the correct fuel mixture of oil and gasoline. Next, check for any air leaks in the carburetor or fuel lines which can prevent proper engine performance.

Additionally, make sure all connections are secure and clean out any debris from around the spark plug. If these solutions don’t work, replace your spark plug or test it with a multimeter to determine if there’s an issue with ignition. Finally, inspect all other components such as hoses, filters & belts for damage or wear & tear that could be preventing your chainsaw from starting up properly.

Why is My Chainsaw Difficult to Start?

If your chainsaw is having difficulty starting, it could be due to a number of factors. The most common problems are related to the fuel mixture in the tank, spark plug fouling, or lack of proper maintenance. If you’re using a 2-cycle engine, make sure that you’re mixing the correct ratio of gasoline and oil.

Also check that your spark plug is clean and properly gapped. In addition, make sure your air filter is clean and not clogged with debris as this can reduce engine performance significantly. Finally, ensure all components such as the carburetor have been regularly serviced; if any parts are worn out or need adjustment they should be replaced or adjusted immediately for optimal performance from your chainsaw.

How Do You Start a Chainsaw That Has Been Sitting?

When starting a chainsaw that has been sitting, make sure to check the gas and oil levels. If they seem low, refill them as necessary. Check all of the parts for any wear or damage, including the chain and bar, spark plug wire connection and air filter.

Once you’ve done this, apply some fresh fuel mix to the carburetor bowl if it is needed before priming the engine with two or three pulls on the starter rope. Finally, start up your chainsaw by pulling firmly but slowly on its starter handle until it turns over and begins running smoothly.

How Many Pulls Should It Take to Start a Chainsaw?

When starting a chainsaw, the number of pulls it should take depends on several factors, such as the age of the saw, its condition and whether or not you are using fresh fuel. Generally speaking, a new chainsaw should start with 2-3 pulls. If your chainsaw is older, then it may take up to 5-6 pulls to get started.

It is important to use good quality fuel (e.g., gasoline mixed with two stroke engine oil), and also make sure that all spark plug connections are clean and secure before attempting to start your chainsaw. Finally, if your attempts at starting still don’t work after several pulls (8-10 maximum), check for any visible blockages in the exhaust system or other parts of the machine before seeking professional help from an experienced technician.

Chainsaw is HARD TO START? Try this EASY TRICK, especially on the BIG Stihl's, Echo's and Husqvarna!

Chainsaw Hard to Start But Runs Fine

A common issue with chainsaws is that they can be difficult to start, but run just fine once started. This may be due to a number of factors such as fuel-air ratio, spark plug fouling, or even an improperly adjusted carburetor. If your chainsaw is having this problem, it’s important to consult a professional for help in diagnosing and fixing the cause of the difficulty starting.

Brand New Chainsaw Won’T Start

If your brand new chainsaw won’t start, the most likely cause is a lack of fuel. Make sure you’ve filled it up with the correct type and amount of oil and gasoline before attempting to start it. Additionally, check that all connections are secure and that there’s no debris blocking the spark plug or fuel filter.

If these steps don’t resolve the issue, consult your owner’s manual for additional troubleshooting advice or contact a local service center for professional help.

Chainsaw Won’T Start After Sitting

If your chainsaw won’t start after sitting for a period of time, there are several potential causes. It could be that the fuel is stale or contaminated and needs to be changed, the spark plug may need to be replaced, air filters need cleaning, or the carburetor may need adjusting. Additionally, it’s important to make sure that you have enough oil in the engine so that it can run properly.

Taking these steps should help get your chainsaw up and running again quickly and easily.

Chainsaw Won’T Start Has Spark And Fuel

If your chainsaw won’t start despite having spark and fuel, it could be caused by the carburetor being out of adjustment. The carburetor regulates air and fuel flow to the engine and must be adjusted properly for efficient operation. You may need to clean or replace the air filter if it is clogged, check or change the spark plug, inspect fuel lines for blockages or leaks, check that all hoses are connected correctly, and look for loose bolts on any components near the engine.

If these steps don’t help get your chainsaw running again you may need professional service from a qualified technician.


Starting a stubborn chainsaw can be a challenging task, but it doesn’t have to be impossible. By following these steps and troubleshooting any potential problems, you can get your saw running in no time. With the right preparation and maintenance, you can help ensure that your chainsaw starts every time without too much effort or frustration.

That way, you’ll always be ready for whatever woodworking projects come your way!

Leave a Comment