How to Change Blade on Skilsaw Circular Saw

To change the blade on a Skilsaw circular saw, start by unplugging the saw and pressing down on the spindle lock button. Rotate the blade until it stops spinning. Then loosen the arbor nut and washer with an adjustable wrench or socket wrench.

Pull off the old blade from its mounting holes and slide in a new one, making sure to match up with all of its mounting holes. Securely tighten the arbor nut and washer before releasing the spindle lock button. Make sure to use safety goggles when changing blades for added protection.

Finally plug back in your circular saw and you’re ready to go!

  • Unplug the Skilsaw Circular Saw: Before beginning any work on a power tool, it is essential to ensure that the device is unplugged and can no longer receive electricity
  • This will help prevent accidents due to unintentional activation of the saw while working with it
  • Remove Old Blade: To change the blade on your Skilsaw, you must first remove the old one from its housing by unscrewing and removing the bolt located at its center point
  • Once you have removed this bolt, pull out gently but firmly on either side of the blade until it comes free from its mounting bracket in order to take it out completely
  • 3
  • Insert New Blade: With your new blade ready for installation, align its hole with that of its mounting bracket before sliding it into place carefully and securely over all four screws so as not to damage them in any way during insertion or rotation of the saw blade itself should they be exposed after alignment has been achieved correctly
  • 4 Securely Fasten New Blade : After inserting and aligning your new circular saw blade properly within its housing unit, replace both washers back onto their respective sides along with tightening bolts once more using an appropriate sized wrench or socket set depending upon what type of fastening system came supplied with yours specifically if different than mentioned here prior being sure to tighten these up sufficiently enough so as not cause slippage during operation when finally put back into use again for cutting various materials afterwards safely time and time again thereafter too!
How to Change Blade on Skilsaw Circular Saw

Credit: sawsonskates.com

How Do You Put a Blade on a Skil Circular Saw?

To properly put a blade on your Skil circular saw, you’ll need to start by unplugging the saw from any power source and then removing the locking pin. Next, locate the spindle lock and turn it counter-clockwise in order to loosen it. You can then lift up the blade guard to access the arbor nut located underneath it.

Finally, use a wrench or an adjustable spanner to loosen and remove this nut before fitting your desired blade onto the arbor shaft – making sure that its teeth are facing downwards – followed by replacing both the nut and guard before finally restoring power to your saw.

How Do I Change the Blade on a Skilsaw 5250 Circular Saw?

Changing the blade on a Skilsaw 5250 Circular Saw is a relatively simple process. First, make sure the power switch is off and then unplug the saw from its power source. Then, remove any screws that may be holding the blade guard in place.

Next, depress and hold down the spindle lock button located on top of your circular saw to keep it from spinning while you are changing out blades. After this, use an Allen wrench or screwdriver (depending on what model you have) to loosen up the arbor nut located near where your blade attaches onto your circular saw. Once it is loose enough, slide off both washers followed by your old blade before finally replacing all components with a new one in reverse order while taking care not to overtighten anything as doing so could damage your parts or cause injury when using it again.

How Do You Lower the Blade on a Skil Circular Saw?

To lower the blade on a Skil circular saw, begin by ensuring that the saw is unplugged from any power source and that you are wearing protective eye wear. Next, locate the depth adjustment lever or knob near the front of your saw. Turn it counterclockwise to loosen it and move it to your desired cutting depth.

To secure this setting in place, turn the knob clockwise until tight. Finally, press down on the blade guard release button while pushing down on the main handle of your saw to lower your blade into position for use.

How Do You Change a Blade on a Skilsaw 5400?

To change the blade on a Skilsaw 5400, first unplug the saw and ensure that it is completely powered off. Then remove the blade guard by unscrewing its mounting screws with a screwdriver or power drill. Lift up the guard to expose the arbor nut, which holds the sawblade in place.

Loosen this nut using an adjustable wrench and carefully lift out both washers and then remove the old blade from between them. Finally, place your new blade between them and tighten down all connections before replacing your blade guard back onto its mountings.

How to Change the Blade on a Skil Saw

How to Change Circular Saw Blade Without Lock

Changing the blade on your circular saw without a lock is possible, but it requires some extra caution to ensure safety. Before attempting this task, unplug the saw and wear protective gloves and eyewear. You should also use a wrench to loosen the bolt that holds the blade in place before removing it from the saw’s arbor.

Once you’ve removed the old blade, secure your new one and make sure that it is tight before plugging in your circular saw again. By following these steps carefully and taking all necessary precautions, you can change out your circular saw blade quickly and easily without having to use a locking mechanism.

How to Change Blade on Skilsaw 5150 Circular Saw

If you need to change the blade on your Skilsaw 5150 circular saw, first make sure that it is unplugged from any power source. Next, loosen the arbor nut and washer by turning them counterclockwise with an adjustable wrench. Pull out the old blade and insert a new one in its place.

Make sure that both sides of the blade have teeth facing outward and tighten the arbor nut and washer securely in a clockwise direction with an adjustable wrench. Once done, plug your circular saw back into a power source and you are ready to start cutting!

How to Change Blade on Skilsaw 5480

Changing the blade on your Skilsaw 5480 is a relatively simple process. First, shut off the power and unplug the saw. Using a wrench, loosen the arbor nut that holds the blade in place until it can be removed.

Place your new blade into position on the arbor shaft and tighten down with an appropriate size wrench or socket. Finally, align your table saw’s fence to 90 degrees before re-engaging power to ensure accuracy of future cuts.

How to Change a Skill Saw Blade

Changing the blade on a skill saw is a fairly simple task that can be done in just a few steps. First, unplug the saw and make sure it’s completely turned off before beginning. Then loosen the arbor nut with an adjustable wrench or other suitable tool and use your hands to remove it from the spindle.

Once removed, you can then slide out the old blade and replace it with a new one being careful to line up its teeth properly with those of the arbor hole. Finally, tighten back down on the arbor nut until secure, plug in your skill saw again, and you’re all set!

Conclusion

Changing the blade on a Skilsaw circular saw is not complicated and can be done in just a few steps. By following these instructions, you will have your new blade installed quickly and easily, so you can get back to working on your project or task at hand. Now that you know how to properly change the blade on your Skilsaw circular saw, you’ll never be caught with an old dull blade again!

Leave a Comment