Start by unplugging the saw and removing the blade guard. Use an Allen wrench to loosen the two screws on top of the saw that secure the upper wheel assembly. Lift off this assembly and set it aside, as well as any other components necessary for access to the blade.
Remove all remaining parts from around or near blade area, including arbor nut and washer, then remove old blade carefully. Inspect new replacement saw blade for cracks or other damage before installing. Place new sawblade onto spindle so teeth point in proper direction before securing with arbor nut & washer.
Reassemble remaining parts including upper wheel assembly which must be tightened securely with Allen wrench provided.
- Step 1: Gather the Materials – To change the blade on your Craftsman circular saw, you’ll need a new blade, a screwdriver, and an adjustable wrench
- Step 2: Unplug Your Saw – Before beginning any work on your circular saw, make sure it is unplugged from its power source
- This will ensure that no electrical shock occurs during the process
- Step 3: Loosen Blade Bolt – Using either a screwdriver or an adjustable wrench, loosen the bolt located at the center of the saw’s blade guard assembly in order to remove it from its housing
- Step 4: Remove Old Blade – Once you have removed the bolt, carefully lift off and remove old blade from its housing
- Discard it properly following all safety guidelines for disposing of sharp objects such as this one
- Step 5: Insert New Blade – Place your new Craftsman circular saw blade into position within its housing and re-secure with bolt previously removed
- Make sure to tighten securely so that there is no play between parts when in motionStep 6 : Plug In Saw – Reattach plug to power source and test out newly installed Circular Saw Blade before use
Credit: thecraftsmanblog.com
How Do You Take the Blade off a Craftsman Saw?
Removing the blade from a Craftsman saw is relatively easy and straightforward. First, make sure to unplug the power cord from the wall outlet. Next, loosen the large nut located on top of the saw that holds the blade in place using a wrench or adjustable spanner.
Once loosened, use your hands to carefully lift up and remove any washers or spacers that may be used to hold down other components of the saw. Finally, carefully remove the blade off its mount by turning it counterclockwise until it comes completely free.
How Do You Change the Blade on a Circular Saw?
Changing the blade on a circular saw is a relatively simple process that requires only a few basic tools. First, unplug the saw and then turn it over to expose the blade guard and arbor nut. Use an adjustable wrench to loosen and remove the arbor nut, which holds the blade in place.
Once removed, carefully slide off the old blade. Install your new blade by aligning its teeth with those of your saw’s drive spindle, making sure that all teeth are lined up properly before securing it in place with your arbor nut. When you have finished replacing the blades, reassemble your saw-making sure all parts are securely tightened-and test it out for safety before using it again!
Which Way Do You Turn to Remove Saw Blade?
When removing a saw blade from your saw, it’s important to make sure you turn it in the correct direction. Most saw blades are designed so that when turning counterclockwise, the teeth of the blade curve up and away from you. This will allow for easy removal without having to worry about getting injured by the sharp edges of the blade or damaging any other components of your machine.
Once loosened, carefully pull out the old blade using a pair of needle-nose pliers and then replace with a new one following these same steps but in reverse order.
How Do You Tighten the Blade on a Old Craftsman Circular Saw?
To properly tighten the blade on a Craftsman circular saw, first make sure that the saw is unplugged from its power source. Then, locate and remove the arbor nut located at the base of your saw blade. Tighten this by hand or with an adjustable wrench until it’s secure.
Once this has been done, place a block of wood between the teeth of the blade and adjust the bevel angle to 90 degrees using a protractor or square. Next, reattach your arbor nut by carefully threading it onto your saw shaft until it is snug against the blade. Finally, use an Allen key to lock in place any set screws found around your arbor nut before plugging back in and testing out your newly tightened Craftsman circular saw!
Beginners Guide Unboxing and Using a Circular Saw
Craftsman 7 1/4 Circular Saw Changing Blade
Changing the blade on a Craftsman 7 1/4 Circular Saw is an easy and straightforward process. All you need to do is first unplug the saw from its power source, then loosen and remove the bolt that holds the blade in place with a wrench. Next, take out the old blade and insert your new one into position making sure that it’s pointing in the right direction.
Finally, use your wrench to tighten up the bolt again before plugging back in your saw and testing it out!
Craftsman Circular Saw Blade Lock
The Craftsman Circular Saw Blade Lock is a great tool for quickly and safely changing circular saw blades without having to use an Allen wrench. It features an easy-grip handle and adjustable lock mechanism that makes locking the saw blade in place effortless. The lock also allows you to easily adjust the depth of cut, which can be especially helpful when working with multiple types of materials or making precision cuts.
This handy device is designed to make your woodworking projects go smoothly and quickly!
How to Change Circular Saw Blade Without Lock
Changing the blade on a circular saw without a lock can seem like an intimidating task, but with some patience and caution it’s actually quite simple. The first step is to unplug the saw from any power source. Then remove the screws that hold the guard in place, as well as any washers or retaining rings that may be present around the blade arbor.
Next, use an adjustable wrench to loosen and completely remove the nut that holds down the blade itself. You should now be able to lift off your old blade and replace it with a new one of equal size—securing it in place by tightening down the same nut you removed before reinstalling all other parts of your tool assembly.
How to Put a Blade on a Circular Saw for the First Time Craftsman
If you’re a beginner to using a Craftsman circular saw, the first step is to ensure that the blade is properly installed. To do this, make sure that there are no obstructions on the arbor of your machine and then align the holes in the center of your blade with those on the arbor. Next, insert and tighten an appropriate size washer and nut onto each side of your blade for additional security.
Finally, use an appropriate wrench to lock down both sides tightly so that it won’t move or wobble during operation. Following these simple steps will have you ready to make all kinds of cuts with confidence!
Conclusion
In conclusion, replacing the blade on a Craftsman circular saw is not difficult. All it takes is a few basic tools and careful steps to ensure safety. With the help of this guide, you can easily learn how to change blades on your Craftsman circular saw in no time at all.
Table of Contents